Teledyne O3 Manual de usuario Pagina 6
- Pagina / 114
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Teledyne API Model 401 O
3
Photometric Calibrator Instruction Manual, 01124, Rev. J2
9.6.4 Checking The DC Power Supply Board................................................................................9-13
9.6.5 Checking The Pneumatic Sensor Board ...............................................................................9-14
9.6.6 Checking The Source Lamp And Detector............................................................................9-14
9.6.7 Checking Main Switching Valve...........................................................................................9-16
9.6.8 Checking The Lamp Power Supply.......................................................................................9-16
9.7
WARRANTY/REPAIR QUESTIONNAIRE .........................................................................................9-18
10 ROUTINE MAINTENANCE ........................................................................ 10-1
10.1
MAINTENANCE SCHEDULE ..........................................................................................................10-1
10.2
LEAK CHECKING .........................................................................................................................10-2
10.3
CLEANING OF SAMPLE CELL.......................................................................................................10-2
10.4 CHANGING THE PROM.................................................................................................................10-3
11 MODEL 401 SPARE PARTS AND EXPENDABLES KITS........................ 11-1
11.1
SPARE PARTS FOR CE MARK UNITS ...........................................................................................11-1
11.2
SPARE PARTS FOR NON-CE MARK UNITS ..................................................................................11-3
Appendix A LIST OF AVAILABLE MODEL 401 OPTIONS ................................................. A-1
Appendix B RECOMMENDED ZERO AIR SYSTEM............................................................. B-1
Appendix C REFERENCES....................................................................................................... C-1
Appendix D SOFTWARE MENU TREES ................................................................................D-1
Appendix E ELECTRICAL SCHEMATIC INDEX ...................................................................E-1
vi
- MODEL 401 1
- CALIBRATOR 1
- SAFETY MESSAGES 2
- TABLE OF CONTENTS 3
- LIST OF FIGURES 7
- LIST OF TABLES 8
- 1 INTRODUCTION 9
- 1.3 Principle Of Operation 10
- 1.3.1 Interferent Rejection 12
- 1.4 Specifications 13
- 1.4.10 Flow Rates 15
- 1.4.11 Power 15
- 1.4.12 Weight 15
- 1.6.1 Electrical Connections 22
- 1.6.2 RS-232 22
- 1.6.3 Pneumatic System 24
- 1.6.5 Output Flow Adjustment 24
- 1.7 Operation Verification 28
- Table 1-1: Test Values 29
- 1.8 Options 30
- 2 OPERATION 31
- 2.1.5 Data Acquisition 32
- 2.1.6 RS-232 Interface 32
- 2.1.7 Password Protection 32
- 2.2 Front Panel 34
- 2.2.3 Status LEDs 39
- 3 CALIBRATION 41
- 3.6 Photometer Calibration 43
- 3.9 Hold Off 45
- 4 SETUP MODE 47
- 4.5 Setting the O 49
- Generation Mode 49
- 4.6 Setting The Time-Of-Day 49
- 4.7 Setting The Date 49
- 4.9 Setting The O 50
- Concentration Range 50
- 4.15 Software Configuration 52
- 0 mV 1000 mV 53
- 5 DIAGNOSTICS 55
- 5.2.1 D/A Output 56
- 6 HANDLING WARNINGS 57
- 7 RS-232 COMMUNICATIONS 59
- 7.1 DAS Reporting 60
- 7.2 Warnings 61
- 7.3 Status/Control 62
- 7.4 Diagnostics 64
- 7.5 Test Measurements 65
- 8 ADJUSTMENTS 69
- 8.4 Flow Readout Adjustment 72
- 8.5 DC Power Supply 74
- 8.6 CPU 74
- 8.7 Status Lines 75
- ± 50 mV 76
- ± 500 mV 76
- 8.12 Bench Feedback Option 78
- 9 TROUBLESHOOTING 79
- 9.2.3 Checking The Keyboard 81
- Table 9-1: Warning Messages 82
- 9.5.5 Cannot Zero 86
- 9.5.6 Cannot Span 86
- Components 87
- 9.6.3 Checking The V/F Card 89
- ° C=2.5V, ± 0.125V/°C 92
- TELEDYNE 96
- 10 ROUTINE MAINTENANCE 97
- 10.2 Leak Checking 98
- 10.3 Cleaning Of Sample Cell 98
- 10.4 Changing The Prom 99
- INTENTIONALLY BLANK 100
- 11 MODEL 401 SPARE PARTS AND 101
- EXPENDABLES KITS 101
- Teledyne API Model 401 O 102
- (table continued) 103
- OPTIONS 105
- Appendix C REFERENCES 109
Relacionado con productos y manuales para De medición, control y control Teledyne O3
(4 paginas)
(42 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales