Teledyne 465L Manual de usuario Pagina 40
- Pagina / 92
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
- OPERATION MANUAL 1
- MODEL 465L 1
- OZONE MONITOR 1
- Notice of Copyright 3
- Trademarks 3
- IMPORTANT SAFETY INFORMATION 5
- CONSIGNES DE SÉCURITÉ 6
- ABOUT THIS MANUAL 7
- REVISION HISTORY 8
- TABLE OF CONTENTS 9
- Teledyne API Model 465L O 10
- Monitor Operation Manual 10
- FIGURES 11
- Teledyne API Model 465L O 13
- 1. INTRODUCTION 15
- APPROVALS 17
- 2.2. Approvals 18
- 3. PRINCIPLE OF OPERATION 21
- 4. GETTING STARTED 23
- 4.1. Pneumatic Connections 25
- 4.1.1. Sample Gas Connection 26
- 4.1.1.1. Sample Filtration 27
- 26 05509F DCN6409 28
- Teledyne API Model 465L O 29
- Monitor Instruction Manual 29
- 4.1.2. Exhaust Connection 30
- Electrical I/O Connections 31
- Configuration 31
- 4.2.2. Analog Output 31
- 4.2.3. Status Outputs 31
- 4.2.6.1. RS232 Connection 35
- 4.2.6.2. RS485 Connection 35
- 4.2.6.3. Ethernet Connection 35
- 05509F DCN6409 35 37
- 6. OPTIONS 39
- 7. OPERATION 41
- Table 7-1: Alarm LED’s 42
- 7.2. Front Panel Menus 43
- 7.2.3. DIAG Menu 47
- 7.2.3.2. Signal I/O 48
- 7.2.3.3. Memory Reset 49
- 7.2.3.4. Zero Calibration 49
- 7.2.3.5. Span Calibration 50
- Figure 7-4: Span Cal Menu 51
- 7.2.4. VIEW Menu 53
- 7.2.5. CONFIG Menu 53
- 7.2.6. SETUP-VARS Menu 54
- 7.2.7. SETUP-STREAM Menu 55
- 7.3. Multi-Stream Operation 56
- 8. DIGITAL COMMUNICATIONS 57
- RS232 Configuration 58
- RS485 Configuration 58
- Ethernet Configuration 58
- 8.3. RS-232 Configuration 59
- 8.4. RS-485 Configuration 60
- 8.5. Ethernet Configuration 61
- (DHCP Mode) 62
- 8.6. MODBUS Register Maps 63
- 62 05509F DCN6409 64
- 05509F DCN6409 63 65
- 64 05509F DCN6409 66
- 9.1. Maintenance Schedule 68
- 9.2. Instrument Layout 69
- 9.4. UV Lamp Adjustment 71
- 9.5. UV Lamp Replacement 72
- Sensor Valve Replacement 74
- Maintenance 75
- 9.11. Boot Loader Operation 76
- 9.11.2.1. Upload Firmware 77
- 9.11.2.2. Verify Firmware 78
- 10. TROUBLESHOOTING 80
- 10.1.2. Interconnect Diagram 81
- LED’s or Status Outputs 82
- 10.2.1. Sensor OK 83
- 10.2.2. Invalid Reading 83
- 10.2.3. Check Lamp 83
- 10.2.4. Pneumatic Error 83
- 10.2.4.1. Pressure Too High 84
- 10.2.4.2. Pressure Too Low 84
- 11. CALIBRATION 86
- 12. SPARE PARTS 88
- M465L NEMA Spare Parts List 89
- 88 05509F DCN6409 90
- 05509F DCN6409 90 92
Relacionado con productos y manuales para De medición, control y control Teledyne 465L
(123 paginas)
(42 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales